A line rarely fails completely. It usually reaches a plateau, and the symptoms on the floor often tell the story long before someone puts together a budget for a study. A conveyor manufacturing company sees these patterns in multiple facilities: a backup forming at the same place along the line, operators quietly compensating at one station, a cluster of rejections at one transfer point, each indicating a conveyor problem in a specific area of the line.
People Also Ask
What is a conveyor bottleneck?
A point on a line where product arrives faster than it can move through, causing the line to stall and limiting throughput.
How do I know if my line needs a retrofit or a full rebuild?
Isolated issues on one or two transfer points are typically remedied through a retrofit. Multiple issues on different transfer points on the same line may indicate a more involved rework.
1. Product Backing Up At The Same Point Every Shift
The same spot, every shift, every time. That’s the pattern. It suggests there isn’t enough space and that you need to change the schedule.
A random place indicates the conveyor is the problem, not the operators or product variety.
2. Operators Manually Feeding Or Straightening Product
Look for a hand reaching in to nudge product back into line every few seconds. This proves there’s a spacing or orientation problem the conveyor should handle on its own, and that line speed is capped by whatever pace a person can manage. Automated cells have the same dependency, since knowing what robotic cells need from their conveyors starts with spacing and orientation.
3. Downstream Equipment Starved While Upstream Runs Full
The gap between them is where throughput is genuinely lost, and it usually traces back to inadequate accumulation conveyor capacity or a transfer that fails to keep pace with the rest of the line.
4. Rejects And Damage Concentrated At One Transfer
Damage scattered randomly along a line probably indicates a problem with the product or its packaging. Damage clustered at a particular transfer point indicates the conveyor belt.
A sharp turn, untimely drop, or worn transfer plate is usually the culprit, and you can fix it by walking the line and watching that area closely. For fragile product, the mechanism matters too. Read our comparison of vibratory feeders and belt conveyors to see how they handle impact differently.
5. Line Speed Increased But Output Unchanged
Turning up the speed dial should increase output. If it doesn’t, the constraint is elsewhere, and accelerating it will only increase rejects and wear without improving the production line’s actual throughput.
6. Frequent Short Stops Rather Than Long Breakdowns
A dozen ten-second stoppages an hour add up to more time lost than a single huge failure, but cause far fewer maintenance calls because no one stop is much of a problem.
Logging them for a shift can often be as surprising as the line downtime itself.
7. Changeover Taking Longer Than The Run
If setup for the next SKU takes longer than the run itself, the conveyor’s tooling and guide rail design work against changeover speed rather than for it.
8. Sanitation Overrunning Its Window
Sanitation overrunning its window is rarely a staffing problem; it’s usually a conveyor built without cleaning access in mind, and every extra minute in the wash bay is a minute the line is not producing. Washdown frequency also drives material choice, which is where aluminum, mild steel, and stainless frames differ most.
9. Every New SKU Requiring A Workaround
New product should not require a jury-rigged guide rail or hand-built bracket to run. When every SKU introduction requires a workaround, the conveyor was sized for one product, not the full range that the plant runs today.
How To Measure Before You Spend
Before upgrading to free up conveyor capacity and increase throughput, measure current throughput per hour or per shift at the point of suspected maximum capacity.
Compare this number to the rated output of the conveying equipment right before and after the process. The difference between those two numbers is what you need to address. Those figures belong in the request itself, alongside the details a conveyor company needs to quote accurately.
When A Retrofit Solves It And When The Line Needs Rework
A single problem transfer, an accumulation gap, or a changeover bottleneck usually responds well to a targeted conveyor retrofit.
Multiple compounding issues across several points on the line are a different story. Line debottlenecking at this scale often means redesigning the path, not patching it one piece at a time. At that point the question becomes how to choose a conveyor manufacturer capable of the rework.
Reading The Floor Before Commissioning
These nine signs are visible on the floor long before a formal study can confirm them. A conveyor manufacturing company that has seen the pattern before often identifies the constraint in a single walkthrough, saving the time and money of a formal diagnosis.
Recognize a few of these on your line? Contact CONOVEY at sales@conovey.com or 1 (844) 876 8889 to talk through what a retrofit looks like for you.
Frequently Asked Questions
Can we retrofit a conveyor and avoid a full line shutdown?
Yes, usually. Often, you can retrofit one transfer point by the time it’s scheduled to be down for another reason anyway.
How much output does a capped conveyor typically cost a plant?
It varies by line and product, but even a single undersized transfer point commonly caps a line well below its rated capacity.
Should I upgrade the whole line or only the bottleneck?
Start with the bottleneck. Upgrading equipment upstream or downstream of the actual constraint rarely changes total output.
Allan Hrynyshyn is a seasoned manufacturing executive and entrepreneur with nearly four decades of experience in conveyor systems, material handling, and industrial automation. He is the Founder and President of CONOVEY, a leading Canadian manufacturer specializing in innovative conveying solutions for the food, packaging, and industrial ...
Read More
End or Center Drive 50-1500mm widths 750-15000 mm lengths Loads up to 50 kg Speeds up to 60 m/min Direct or chain drive Roller ⌀50-100mm Optional ⌀16mm nose V-Guide option
End Drive 50-1500mm widths 750-15000 mm lengths Loads up to 250 kg Speeds up to 60 m/min Direct or chain drive Roller ⌀50-100mm Optional ⌀16mm nose V-Guide option
End or Center Drive 50-1500mm widths 750-15000 mm lengths Loads up to 50 kg Speeds up to 60 m/min Direct or chain drive Roller ⌀50-100mm Optional ⌀16mm nose V-Guide option
End Drive 50-1500mm widths 750-15000 mm lengths Loads up to 250 kg Speeds up to 60 m/min Direct or chain drive Roller ⌀50-100mm Optional ⌀16mm nose V-Guide option